Furnace Replacement Cost in Seattle, Washington
Expect to pay $4,700 to $11,600 for furnace replacement in Seattle, WA. Most homeowners end up near $8,500, depending on the equipment tier and how much of the old setup can be reused.
Compare Free Quotes in Seattle
Seattle Weather and HVAC Load
In a normal year, Seattle racks up 4,482 heating and 210 cooling degree days (NOAA 1991-2020 normals). Heating is the bigger job here, and furnaces and heat pumps in Seattle put in far more hours than the air conditioner. On average, Seattle gets 25 freezing nights and 2 days above 90°F per year. Snowfall averages about 4 inches. For a 2,000 sq ft house, this climate points to a heating load somewhere near 55,000 BTU/h. Treat that as a starting number. A Manual J calculation will move it up or down based on insulation and windows.
| Heating degree days / year | 4,482 |
|---|---|
| Cooling degree days / year | 210 |
| Nights at or below 32°F | 25 |
| Days above 90°F | 2 |
| Average low / high | 45.7°F / 60.8°F |
Seattle Housing Stock
Census figures put the median build year in Seattle at 1974, so a typical house here has about 52 years on it. A lot of these homes are on their second or third system by now. The ductwork is usually original, and leaky joints are common. Seattle has roughly 156,000 owner-occupied homes, or 44.2% of households. Homes here have a median value of $912,100 and households a median income of $121,984. Those two numbers drive the labor adjustment in our estimate.
NOAA's Storm Events Database shows no hail or damaging-wind days for King County from 2020 through 2025, so storm damage to outdoor units is rare here.
When Replacement Makes Sense
- A repair quote runs past a third of the cost of a new unit
- The furnace is 15 to 20 years old or more
- Gas or electric bills keep climbing even though usage hasn't changed
- A tech found a cracked heat exchanger, or the CO detector has gone off
What Moves the Price
- BTU size, which should come from a Manual J load calculation
- Single-stage, two-stage or modulating gas valve
- New PVC venting if you move to a condensing model
- Condition of the existing ductwork and any changes it needs
- Permit and inspection fees, which the local building department sets
- AFUE rating: a basic 80% unit vs. a 96% condensing furnace
We raised the national figures about 48% for Seattle using local income, home values and the equipment size this climate needs. Real bids can still come in outside the range, so collect three written quotes.
What the Quote Should Cover
- The new furnace, filter rack and thermostat wiring
- Combustion and safety tests
- Gas line and vent connections
- Removing and hauling away the old furnace
- The permit and the manufacturer warranty registration
Washington Permits, Efficiency Rules and Rebates
Washington falls in the DOE's North region. New split central air conditioners must meet at least 13.4 SEER2, and heat pumps sold anywhere in the U.S. need 14.3 SEER2 and 7.5 HSPF2. Plan on a mechanical permit for most replacements in Seattle; the contractor normally pulls it. Before you sign, ask each bidder for their Washington license or registration number and proof of insurance. The federal 25C tax credit ended for equipment installed after December 31, 2025, so incentives now come mostly from utilities and state programs. Check your electric and gas utility's rebate page before you pick equipment.
Before You Hire
- Make sure all three quotes are for the same AFUE and staging, or you can't compare them.
- Ask for the Manual J load calculation in writing. Oversized furnaces are the most common mistake we see.
- Replace it in early fall if you can. A no-heat emergency in January costs more and leaves you fewer choices.
Get Free Furnace Replacement Quotes in Seattle
Tell us where you are and up to three licensed local pros will get in touch. You don't have to hire any of them.
Furnace Replacement Questions from Seattle Homeowners
How much is furnace replacement in Seattle?
Plan on $4,700 to $11,600, with most jobs near $8,500. Equipment efficiency, house size and the condition of the ducts and wiring decide where your quote falls.
When is the best time to schedule furnace replacement in Seattle?
Between late spring and early fall. Seattle averages 25 freezing nights a year, and heating calls spike from November through February.
How long does a furnace replacement take?
A straight swap is usually done in one day, somewhere between 4 and 10 hours. Moving to a condensing furnace with new PVC venting can add a few more.
Is a high-efficiency furnace worth it?
In cold climates, a 95%+ AFUE furnace usually earns back the price difference in lower gas bills. Where winters are mild, the payback can take a very long time.
Furnace Replacement Near Seattle
Sources: U.S. Census Bureau ACS 5-year estimates 2019-2023 and 2024 population estimates; NOAA NCEI U.S. Climate Normals 1991-2020, station Seattle Sand Point Wsfo; NOAA Storm Events Database 2020-2025, King County. Prices are our estimates, not contractor quotes. Updated 2026.